Knowing how to use bubble wrap properly comes down to knowing the answer to three main questions:
- Should the bubbles face inwards or outwards?
- How many layers should there be on every side?
- Should bubble wrap be taped closed?
Get those right and most breakages that start on the packing bench disappear, because the wrap can’t loosen in transit. This guide is for despatch, warehouse and removals teams, who want to make sure products are well protected in transit.
In this article, we’ll cover:
- Which way bubble wrap should face, and the one exception to the rule
- How many layers to use for standard, heavy and fragile items
- When to choose 9.5mm bubbles and when to step up to 32mm heavy-duty wrap
- How to pack faster with perforated rolls, dispensers and bulk buys
- How to wrap furniture for removals and office moves, and whether bubble wrap insulates
Which way does bubble wrap go: bubbles in or out?
Bubble wrap goes bubbles in, facing the product, with the flat side outwards. The bubbles are the cushioning, so they need to sit against the item where they can compress and absorb a knock.
That’s the short answer to the bubble wrap in or out question, and it’s the one most packing teams get wrong more often than you might expect. New starters often ask ‘which way does bubble wrap go?’, so it’s worth a sign above the bench. With the flat side facing out, the outer layer also slides against box walls and other parcels without the bubbles snagging or bursting. That matters on conveyors and in courier cages, where parcels get pushed and stacked many times before delivery.
The exception: glossy and freshly finished surfaces
High-gloss lacquer, piano finishes and freshly painted items need a barrier layer between the surface and the bubbles. Bubbles pressed into a soft or warm finish for several days can leave a dimpled pattern.
Put a sheet of tissue or packing paper against the surface first, then wrap with the bubbles facing in as normal. You keep full cushioning and avoid marking the finish.
How to use bubble wrap on the packing bench
Using bubble wrap well is mostly about consistency. When every packer follows the same routine, you’ll see fewer damage claims and less wasted material.
Here’s a simple routine for how to use bubble wrap for packing on a busy bench:
- Measure the item and cut enough wrap to go fully around it with at least a 5cm overlap
- Place the item on the wrap with the bubbles facing up towards it
- Roll the item, keeping the wrap snug but not stretched tight
- Fold in the ends and tape the wrap closed rather than tucking it
- Box the item with void fill and run a quick shake test
The tape step is the one most often skipped. Wrapping with bubble wrap and tucking the ends looks neat at the bench, but tucked ends work loose as soon as the parcel’s shaken. A single strip of packing tape across the seam keeps the wrap where you put it.
The shake test catches what the eye misses. Close the box, give it a gentle shake and listen. If anything moves, add void fill until it doesn’t.
How many layers of bubble wrap do you need?
Most goods need one complete layer with a generous overlap, while fragile items such as glassware and ceramics need two or three. As a rule of thumb, aim for around 5cm of cushioning between the product and every wall of the box.
That 5cm can come from bubble wrap alone or from bubble wrap plus void fill. For heavy items, add an extra layer under the base, because that’s where the impact lands when a parcel’s dropped.
How to bubble wrap wine glasses and other glassware
Glassware needs support inside the bowl as well as around it. If you’re working out how to bubble wrap wine glasses for despatch, start by filling the bowl loosely with crumpled packing paper.
Wrap the stem next with a narrow strip of small-bubble wrap, then wrap the whole glass in two layers with the bubbles facing in. Pack glasses upright, never touching, with dividers or void fill between them.
Small or large bubbles: which bubble wrap should you use?
Use small bubbles for surface protection and lighter items, and large bubbles for heavier products and for filling space. For most e-commerce goods, 9.5mm bubble wrap gives the right balance of cushioning and flexibility.
Larger bubbles hold more air, so they spread the force of an impact over a wider area. For machinery parts, large ceramics and flat-pack furniture, switch to heavy-duty extra-large bubble wrap such as RAJA Heavy Duty Bubble Wrap Rolls with 32mm bubbles.
Small bubbles have their own advantage: they wrap tightly around corners and curves. That makes them the better choice for small electrical items, bottles and anything with an awkward shape.
How to pack faster with bubble wrap
The quickest time saving comes from cutting less by hand. Pre-perforated rolls, a dispenser at the end of the bench and fewer reorders all reduce the time each parcel takes.
A perforated bubble wrap roll tears cleanly at set intervals, so packers pull off a consistent length without reaching for a knife. RAJA Perforated Bubble Wrap Rolls use 9.5mm bubbles and contain 30% recycled material.
Mounting the roll in a bubble wrap dispenser with cutter keeps it off the floor and within reach. It also stops the roll unwinding across the bench, which wastes material and gets in the way.
High-volume sites can cut reorders by buying in pallet quantities. RAJA Bubble Wrap Rolls are available as a bulk large bubble wrap pallet buy, also made with 30% recycled content.
How to wrap furniture with bubble wrap for removals and office moves
Furniture needs its corners and edges protected first, then a full wrap to stop scuffs and dents. For removals firms and office relocations, that means corner protection plus a soft, wide roll of furniture bubble wrap.
Fit corner protectors for furniture to tables, cabinets and frames before you start wrapping. Corners take the first hit when furniture is carried through doorways or loaded into a van. Our wider range of corner protectors also includes foam and cardboard profiles for long edges.
Next comes the wrap itself. Jiffy FURNI-Soft bubble wrap rolls are made for furniture, with 9.5mm bubbles and 30% recycled content. Wrap pieces with the bubbles facing in and tape every seam.
Good protective packaging for furniture works in layers: corners first, bubble wrap second and a dust cover on top for anything going into storage. Bubble wrap for removals jobs should go on last thing before loading, so it stays clean and intact.
Office moves: screens and electronics
Office moves add monitors, printers and IT kit to the furniture list. Wrap screens with the bubbles facing the glass, add a layer of card over the front and label each one ‘screen side’ so it’s loaded upright.
Remove ink cartridges and loose trays from printers before wrapping. Anything that can move inside a machine can damage it in transit.
Is bubble wrap a good insulator?
Bubble wrap is a good insulator for short journeys, because each bubble traps still air and still air slows the movement of heat. It isn’t a substitute for purpose-made insulated packaging when goods must stay within a set temperature range.
Insulated bubble wrap usually adds a foil face, which reflects radiant heat as well as trapping air. It’s useful for keeping products a little cooler or warmer for a short journey, but it won’t hold chilled food or medicines at temperature for long.
For temperature-sensitive shipments, a fitted box liner is more reliable. The RecyCold Climaliner is an insulated thermal box liner that sits inside a standard corrugated box. Standard bubble wrap still has a job inside the liner, wrapping individual items to stop them moving.
Putting it into practice
Training new starters on how to use bubble wrap takes minutes, and most mistakes are habits rather than material problems. Write your routine down at the packing bench: bubbles in, 5cm of cushioning, taped seams and a shake test before the box is sealed.
Then match the material to the job. Use 9.5mm wrap for everyday goods, 32mm heavy-duty wrap for weight, and corner protectors and furniture rolls for removals.
Stock up your packing bench
Whether you need a single bubble wrap roll for an office move or pallet quantities for a busy dispatch floor, we can help. Our range includes 9.5mm and 32mm bubbles, perforated rolls and dispensers.
Key takeaways
- Bubble wrap should face bubbles in, towards the product, with the flat side outwards to protect the bubbles from snagging.
- Aim for around 5cm of cushioning between a product and every wall of the box, using bubble wrap and void fill together.
- Use 9.5mm bubbles for everyday goods and 32mm heavy-duty bubble wrap for heavy or awkward items.
- Perforated rolls and a dispenser with a cutter cut the time it takes to wrap each parcel.
- Furniture needs corner protectors fitted first, then a full wrap with every seam taped.
FAQ: Bubble wrap for packing and moving
How much bubble wrap do I need to move house?
How much bubble wrap you need to move depends on what you own, but allow one 50-metre roll for a one-bedroom home as a rough guide. For bubble wrap for moving house with three bedrooms, allow two or three rolls, plus extra for glassware and mirrors.
What’s the best bubble wrap for moving?
The best bubble wrap for moving is a small-bubble 9.5mm roll, because it wraps tightly around most household items and is easy to handle. Add a roll of large-bubble wrap for heavy items and to fill gaps in boxes.
Can you reuse bubble wrap?
Yes, bubble wrap can be reused as long as most of the bubbles are still intact. Flattened wrap still gives some surface protection, but don’t rely on it for fragile items.
Should I wrap plates individually?
Yes, wrap every plate individually and pack them on their edges, like files in a drawer. Plates stood on edge are far less likely to crack than plates stacked flat.
Should a mattress be wrapped in bubble wrap?
No, a mattress is better protected in a purpose-made mattress bag. Bubble wrap can trap moisture against the fabric if the mattress goes into storage.
How should I store leftover bubble wrap?
Store rolls upright in a cool, dry place away from direct sunlight and sharp edges. Heat and pressure from heavy stock stacked on top will slowly flatten the bubbles.





